NEGEL TOOL BOX

Diesel injector copper washer remover install tool, 50629
Size: inner hole 7mm

•     Designed for use on most Common Rail CDI injectors to remove copper washer sealing the base of the injector.
•     Suits most European cars using Bosch CDI fuel injection
•     Handy screw thread and expanding jaw design
•     Remove and install the copper washers on diesel injectors quickly and effectively with this special tool.
•     The reach of 230mm long is designed to install copper washers on deep seated injectors.
•     For removing and installing the copper wires on diesel injector.
•     Quick & effective. Reach - 230mm.

    For deep seated injectors.
    Manufactured from Chrome Vanadium...

Cam belt tension gauge, 50607

Suitable for belts of varying thickness.
Dual scales allows the measurement to be taken from either side of the tool.
Knurled knob measurement.
Lenght (approx): 85 mm - 100 mm
Wight: 80 mm

Made in China

Universal Tie rod wrench, 50444

Features:
Designed specifically for the removal of the direction of the steering rod.
The master tie rod tools easily replace inner tie rod ends.
Applicable to various vehicles: Mercedes Benz, BMW, Toyota, Honda, Ford,  Nissan , etc.

Engine Timing Tool Set BMW Mini, PSA 1.4 & 1.6, Citroen, Peugeot, 780-8162

Suitable for timing 1.4 & 1.6 Valvetronic direct injection petrol, chain drive engines, fitted in BMW Mini, Citroen and Peugeot vehicles.
Content:

• Camshaft Locking Tool - Inlet
• Camshaft Locking Tool - Exhaust
• Camshaft Alignment Clamp
• Crankshaft Setting Pin
• M6 Setscrews (4)
• Chain tensioner

Models:

• Mini One Coupe R56 (2006-2010)
• Mini Cooper Coupe R56 (2006-2010)
• Mini Cooper HB R55 (2007-2010)
• Citroën C4 (2008-2009)
• Citroën C4 Picasso (2008-2009)
• Peugeot 207 (2006-2010)
• Peugeot 207CC (2007-2010)
• Peugeot 308 (2001-2010)
• Peugeot 3008 (2009-2012)
• Peugeot 5008 (2009-2012)

 Engine Codes:

• N12
• N14
• EP3 (8FS)
• EP3C (8FR)
• EP6 (5FW)
• EP6C (5FS)
• EP6DT (5FT)
• EP6DT (5FX)
• EP6CDT (5FV)
• EP6DTS (5FY)

Code: 52046

Mede in Taiwan

•  

Diesel Injector extractor set, 50633

For removal of diesel injectors
Various adaptors make the kit suitable for most diesel injectors
Includes also the following components:
M14 x 1.5 for Delphi adaptor
M17 x 1 for Bosch adaptor
M20 x 1 for Denso adaptor
M25 x 1 for Siemens adaptor
M27 x 1 for Siemens adaptor
M27 x 1 for Bosch injector nozzle adaptor

Puller with M14 x 1.5P

3 x different slide hammers:
1.6 kg, 160 mm length
2.7 kg, 460 mm length
5.1 kg, 600 mm length

2 x pulling claws with fork opening:
13.7 x 18 mm, 105 mm length
12.7 x 19 mm, 130 mm length

5 x  Oxygen Sensor slotted 6-pt 1/2" sockets, 100 mm length sizes 25 - 27 - 28 - 29 - 30 mm

Injector extractor, sleeve design, with shells outer diameter 35 mm, internal diameter 29 mm, M17 x 1.0 spindle
Pulling adapter with external thread M27 x 1.0 (3pcs) and M25 x 1.0
Pulling adapter with internal thread M27 x 1.0 (3pcs)
Sliding hammer adapter for inner, outer and claw extractor.

Made in China

14 Pcs Injection Puller Tool Bosch, Delphi, Denso and Siemens Diesel Injector Remover, 50348

Application:

Suitable for the fast and reliable removal of Bosch, Delphi, Denso and Siemens diesel Injectors.

Includes:

Comprehensive set of 1/2in.Dr Injector Sockets - 25, 27, 29, 30 mm

7 Injector Adaptors and Slide Hammer

Blow mold case for storage

Contains:

Impact Hammer: 3.6 kg

Overall length (. M handle) slide hammer: 510 mm

- Length of the handle: 110 mm

- Ball joint adapter

- Adapter: M14 x 1.5 for Delphi

- Adapter: M17 x 1 for Bosch

- Adapter: M20 x 1 for Denso

- Adapter: M25 x 1 for Siemens

- Adapter: M27 x 1 for Siemens

- Adapter: M27 x 1 for Bosch

- 4 slotted 6-point socket wrench inserts ( 100 mm long) for electrical unit: 25 - 27 to 29 - 30mm

- 10 mm hex bit application, 1/2 "drive

Made in China

Bearing separator 105 - 150 mm, 50132-4

Capacity: 105 - 150 mm
Bolt size: Ø 19 mm, 260 mm
Bolt thread: 3/4" x 16 UNF
Body thread: 5/8" x 11 UNC
Drop forged
Chrome finish

Bearing separator 75 – 105 mm, 50132-3

Bearing separator 50 - 75 mm, 50132-2

Capacity:2" 1/4"- 3 1/2". (50mm x 75mm)
Bolt 12.7 x 135 mm, thread 1/2" x 20UNF
Body thread 3/8" x 16UNC
HRC 38-45°
Forged
Chrome plated

Bearing separator 30-50 mm, 50132-1

-  Capacity: 30mm x 50mm  (1-1/4" to 2-1/4")
-  Bolt 9.5 x 125 mm, thread 3/8" x 24UNF
-  Body thread 3/8" x 16UNC
-  HRC 42-45°
-  Forged
-  Chrome plated

Overhead valve spring compressor, 50109

Description: This overhead valve spring compressor is ideal for removing valve springs, spring retainers by compressing the valve spring retainer and exposing the valve keeper, remove keepers, uncompressing the tool then remove spring. It features a reversible jaw / adaptor and automatic cam-action locking to a re-determined setting.
Specifications:
Easy to operate
Cam action level design for secure valve spring locking into the tool
Allow valve springs and valve stem oil seals to be replaced with the cylinder head
Tool spring depth reach grips to retainer are adjustable to fit most large and small spring applications
For use on a wide range of OHV, OHC and CHV engines.
Not suitable for use on engines with deep seated valves

Made in China

Draper Bearing, Seal and Bush Insertion/Extraction Kit (26 piece), 50092A

Expert Quality, bearing, seal and bush insertion and extraction kit, perfectly designed to aid with accurate and controlled insertion or removal of a host of different bearings, including normal bearings, silent bearings, hydraulic bearings, rubber bearings, bearing bushes, shaft seals etc.
Each kit comprises of 22 adaptor rings and five fine thread puller bars with hex. nut ends, contents of each kit is the following:

1 x 34mm x 44mm adaptor ring, 1 x 36mm x 46mm adaptor ring, 1 x 38mm x 48mm adaptor ring, 1 x 40mm x 50mm adaptor ring, 1 x 42mm x 52mm adaptor ring, 1 x 44mm x 54mm adaptor ring, 1 x 46mm x 56mm adaptor ring, 1 x 48mm x 58mm adaptor ring, 1 x 50mm x 60mm adaptor ring, 1 x 52mm x 62mm adaptor ring, 1 x 54mm x 64mm adaptor ring, 1 x 56mm x 66mm adaptor ring, 1 x 58mm x 68mm adaptor ring, 1 x 60mm x 70mm adaptor ring, 1 x 62mm x 72mm adaptor ring, 1 x 64mm x 74mm adaptor ring, 1 x 66mm x 76mm adaptor ring, 1 x 68mm x 78mm adaptor ring, 1 x 70mm x 80mm adaptor ring, 1 x 72mm x 82mm adaptor ring, 1 x 75mm x 85mm adaptor ring, 1 x 80mm x 90mm adaptor ring, 1 x M10 pulling spindle, 1 x M12 pulling spindle, 1 x M14 pulling spindle, 1 x M16 pulling spindle.

Made in China

Draper Bearing, Seal and Bush Insertion/Extraction Kit (27 piece), 50092

Expert Quality, bearing, seal and bush insertion and extraction kit, perfectly designed to aid with accurate and controlled insertion or removal of a host of different bearings, including normal bearings, silent bearings, hydraulic bearings, rubber bearings, bearing bushes, shaft seals etc.
Each kit comprises of 22 adaptor rings and five fine thread puller bars with hex. nut ends, contents of each kit is the following:

1 x 34mm x 44mm adaptor ring, 1 x 36mm x 46mm adaptor ring, 1 x 38mm x 48mm adaptor ring, 1 x 40mm x 50mm adaptor ring, 1 x 42mm x 52mm adaptor ring, 1 x 44mm x 54mm adaptor ring, 1 x 46mm x 56mm adaptor ring, 1 x 48mm x 58mm adaptor ring, 1 x 50mm x 60mm adaptor ring, 1 x 52mm x 62mm adaptor ring, 1 x 54mm x 64mm adaptor ring, 1 x 56mm x 66mm adaptor ring, 1 x 58mm x 68mm adaptor ring, 1 x 60mm x 70mm adaptor ring, 1 x 62mm x 72mm adaptor ring, 1 x 64mm x 74mm adaptor ring, 1 x 66mm x 76mm adaptor ring, 1 x 68mm x 78mm adaptor ring, 1 x 70mm x 80mm adaptor ring, 1 x 72mm x 82mm adaptor ring, 1 x 75mm x 85mm adaptor ring, 1 x 80mm x 90mm adaptor ring, 1 x M10 pulling spindle, 1 x M12 pulling spindle, 1 x M14 pulling spindle, 1 x M16 pulling spindle, 1 x M18 pulling spindle.

The set is in case.

Made in China

Universal ball joint puller, automobile, 23 mm, 50049

Specification:
External clamping width: 23 mm
Clamping depth: 65 mm
Width: 100 mm
Spindle length: 35 mm
Thread dimension: M14 x 1.5
Width across flats: 19 mm

Applicable:
For easy ejection of ball joint bolts, particularly for many cars from the following manufacturers: Audi, BMW, Fiat, Ford, Daimler-Chrysler, Opel/Vauxhall, Nissan, Toyota, VW, Volvo.

Door upholstery tack remover, 50939

Designed to remove the car door panel.
Comfortable extended handle.
Made of heat treated carbon steel.
Screwdriver length: 200 mm

Made in China