NEGEL TOOL BOX

21 PCS Universal Brake Caliper Wind Back Kit Suitable for push back and wind back brake pistons. Includes left- and right-handed thrust bolt assemblies. Left-handed thrust bolt required for Ford, Citroen and Renault applications. Adaptor plates with thrust bolt assembly and reaction plate. Helps prevent damage to pistons and seals. Updated adaptor set suitable for a wide variety vehicles. Supplied in carry-case.

12 pcs Bearing separator 30-75 mm, 50132

Bearing separator included 30-50 mm & 50-75 mm. Pull out the bearing wth the H-type beam and bolts.
Bearing separator tools are used with bar puller and legs for a wide variety of pulling jobs.

17 pcs proffesional slide hammer/puller set, 50139A
Features:
Designed to use with other 5/8" - 18 thread slide hammer attachments.
Internal and External jaws provide a variety of combinations to pull bearings, gears and seals
Pulls flange-type rear axle and most front wheel drive hubs.
Set includes grip wrench adapter and dent puller
Two and three way cross blocks and cone provide perfect jaw configuration for many jobs
Drop forged steel puller and fully hardened shaft and accessories.
Converts in to 2 or 3 jaw internal / external puller.

Fuel injection test set, 50199

The car fuel pressure diagnostic kit is suitable for most vehicles with a fuel injection system with petrol or gas engines (except Bosch, CIS Jetronic, Throttle Body Systems on GM cars).
Not suitable for diesel engines with high pressure injection pump or direct injection engines due to the low pressure range of the manometer.
Fuel pressure testing is an essential part of the fuel injection system troubleshooting process.
Contents:
The set is equipped with various fittings and connection hoses for testing.
15 "length hose is used for direct connection to 1/4" SAE standard fuel pump shredder valve
An 8 "length hose is for the M6 ​​fuel pressure test hole, and there are also adapters M8; M10; M12; M14 for the corresponding test port on fuel rail.
Aluminum tee to support the connection between the fuel pump and the engine for most cars.
Manometer, protected with a rubber shell, with a diameter of the dial 3-1 / 2 ", with a range of 0-10bar (0-140psi) and two-color coded scale for easy reading. The hoses use rubber nylon resin and the built-in nylon can strengthen the hose with increased stress resistance. The pressure relief valve and 16 "fuel drain hose help to safely release the pressure and easily restore the fuel.
Fuel pump pressure check:
The manometer is designed to easily and quickly check the pressure of the fuel injection pump and the fuel flow.
You can compare the pressure value with the manufacturer's recommended reference range to help diagnose the petrol engine system.
Low fuel pressure can be caused by kink/leak/clog on inlet supply side components, a bad fuel pump or regulator, low tank pressure
High fuel pressure may be caused by a bad fuel pressure regulator or kincked outlet return line.

Made in China

Hose clamp pliers with red coating, 780-0074

These pliers have a ratchet locking mechanism.
Holds the bracket in an open position for easy removal and installation.
Comfortable handle with ergonomic grip.

Made in Taiwan

45° Hose clamp pliers with red coating, 780-0068

45° Hose clamp pliers with red coating, 780-0058A

Features: To remove and install clamps for hose connections in hard-to-reach areas.
The jaws are curved at 45 °.
With ratchet locking mechanism.
Comfortable handle with ergonomic grip.

Made in Taiwan

1/2”DR. Pin Wrench Socket For Mercedes-Benz M-Class (W163/W164), 846-7037А

Application: For Mercedes Benz ML class W163 until June 2005 and W164 from 2005
To replace hinges on the front and rear axle.
Facilitates loosening and tightening the torque lock nuts with correct torque
Suitable for lower suspension connections on the front and rear axles
• Application: For Mercedes-Benz M-Class hinges (W163 / W164) on the front and rear axles.
• Used to fasten the retaining ring during the replacement of the ball joints.
• Precision fitting.
• Material: Cr-Mo
• Inside Diameter: 52 mm
• Outside Diameter: 63 mm
• H: 32 mm

Made in Taiwan

3/4”DR. Pin Wrench Socket For Mercedes-Benz M-Class (W163/W164), 846-7037B

Application: For Mercedes Benz ML class W163 until June 2005 and W164 from 2005
To replace hinges on the front and rear axles.
Facilitates loosening and tightening the torque lock nuts with correct torque
Suitable for lower suspension connections on the front and rear axles
• Application: For Mercedes-Benz M-Class hinges (W163 / W164) on the front and rear axles.
• Used to fasten the retaining ring during the replacement of the ball joints.
• Precision fitting.
• Material: Cr-Mo
• Inside Diameter: 52 mm
• Outside Diameter: 63 mm.
• H: 60 mm

Made in Taiwan

Engine timing tool kit - VAG VW AUDI 1.4 1.6 2.0i TDi CR 2012 ON, 780-8364

An 8 piece kit consisting of the components required to lock the crankshaft. Cam pulleyand fuel pump pulley in their timed positions to allow the removal and replacement of the camshaft timing belt
Contents:
A. 2.5mmTensioner Locking Tool, OEMT10265

B.Auxiliary Drive Tensioner Pin, OEMT10060A

C.Cam Shaft Pulley Timing Pin, OEM 3359

D.Fuel Pump Holding Tool, OEMT10051

E.Crankshaft Timing Tool, OEMT10490

F. 6mm Ball Hex Key, OEMT10264
G.Pin for E
Application: Post 2012 1.6 & 2.0 TDI Common Rail Diesel engines found in the Audi, Seat, Skoda and Volkswagen:
VW: Golf SV/Sportsvan, Golf VII, Golf VII Estate, Golf VII Wagon, Polo
SEAT: Leon, Leon ST
AUDI: A3 Cabrio, A3 Saloon, A3 Sedan, A3/A3 Sportback, A4, A4 allroad, A4 quattro,A5 Coupe/Cabriolet, A5 Sportback, A6, Q5,TT
SKODA: Octavia III
Engine: 1.4TDI CR, 1.6TDI CR, 1.6TDI CR GreenLine, 1.6TDI CR BlueMotion, 1.6TDI CR Ecomotive, 2.0TDI CR, 2.0 RS TDI CR, 2.0TDI CR Ultra
Engine code: CKFB, CKFC, CLHA, CLHB, CNHA, CNHC, CRBC, CRBD, CRFA, CRFC, CRKA, CRKB, CRLB, CRLC, CRMB, CRVA, CRVC, CSUA, CSUB, CUNA, CUPA, CUTA

Made in Taiwan

VW & AUDI Strut nut socket, 210-0155-AT

Features:
Suitable for the disassemble and installation of top shock retaining nut.
Used with 22mm spanner wrench.
Material: Heat treated and tempered chrome molybdenum steel (CR-MO)
Overall Length: 44mm
Applications: Most Audi & VW front wheel drive vehicles.

Made in Taiwan

Auto body repair pull clamp (Two way),113-01027NN

Compact and suitable for use in different spaces.
With two-way direction:
-Cross capacity: 2 tons
- Longitudinal capacity: 3 tons
- Gripping Surface: 37mm (wide) / 15mm (deep)
- Material: Cr-Mo
Bolt size: 14 mm x 120 mmL
Zinc plated. Corrosion resistant.

Made in Taiwan

Auto body repair pull clamp (Two way),113-01017C

Compact and suitable for use in different spaces.
With two-way direction:

-Cross capacity: 2 tons
- Longitudinal capacity: 5 tons
Bolt size: 16 mm x 70 mmL
Zinc plated. Corrosion resistant.

Made in Taiwan

Small mouth pull clamp, 113-01017A

Suitable for use in confined spaces.
One-way direction  of work.

Bolt size: 16 mm x 70 mmL
Capacity: 5 t
Zinc plated. Corrosion resistant.

Made in Taiwan

36 mm Viscous fan hub spanner, 058-6227A

Features:
For disassembly of FORD and GM (Opel / Vauxhall) viscous hub fins.
Cranked design for easy access.
Made of pressed, tempered, hardened and chromed steel with PVC handle.

• Size: 36mm.
• Lengh: 270 mm

Applicable:
Ford Granada 2.4 & 2.9; GM Carlton, Manta & Senator

Made in Taiwan